SPECIFICATIONS

Brand Name: NoEnName_Null

Is Electric: No battery

Origin: Mainland China

Material: Metal

Recommend Age: 14+y

RC Parts & Accs: Radio Systems

For Vehicle Type: Airplanes

Use: Vehicles & Remote Control Toys

Remote Control Peripherals/Devices: Remote Controller

Tool Supplies: Battery

Quantity: 1 pcs

Four-wheel Drive Attributes: Motors

SpeedyBee F405 V3 Flight Controller 
MCU:STM32F405
IMU (gyroscope):BMI270
USB Port Type:Type C
Barometer:Internal
OSD Chip:AT7456E Chip
BLE Bluetooth:Support, for parameter tuning
DJI Air Unit Connection Method:Support 6pin socket direct connection, welding wire connection two ways
MicroSD Card Slot Blackbox:Support, please use a MicroSD card of SDSC/SCHC type below 4GB, which must be formatted in FAT16/FAT32 format. Do not use SDXC type cards. Note: Betaflight only supports up to 4GB
Galvanometer Input: Supported. When paired with SpeedyBee BLS 50A ESC, please set Scale=386, Offset=0
Betaflight camera parameter adjustment pad: Support (front CC pad)
Power input:3S - 6S Lipo (Through the 8pin interface on the back or the G, BAT pins/pads in the pads)
5V BEC Output :
9 groups of 5V output, (4 +5V pads on the front and 1 BZ+ buzzer pad, and one +5V pad on each of the 4 corners for external LED lights), the total current output is 2A
9V BEC Output :
2 groups of 9V output, (1 +9V pad on the front, +9V output in a seat on the back), the total current output is 2A
3.3V BEC Output :
1 group (1 3.3V pad on the front), the maximum current is 500mA
4.5V BEC Output :
2 groups (2 4.5V pads on the front), the maximum current is 1A
ESC signal: M1-M4 on the back and M5-M8 on the front
UART serial port: five groups of serial ports (UART1, UART2, UART3, UART4 , UART6)
ESC telemetry input: R4 (UART4)
I2C:Support. SDA, SCL pads on the front. For magnetometers, sonar, etc.
Legacy Betaflight LED Pads: Supported. 5V, G, LED strip on the bottom of the front. For BF control WS2812 LED light
Buzzer:Support .BZ+ , BZ- pad used for 5V buzzer
BOOT key:
Supporte.Press and hold the BOOT key to power on, you can enter the DFU mode, which is used to save the brick and flash the firmware; in the power-on standby state, the BOOT key is also used to control the LED strips connected to the D1-D4 pads on the four corners of the PCB. By default, short press the BOOT key to cycle through the LED display status; Changan BOOT key switches the LED control mode: SpeedyBee LED or BF LED. In BF LED mode, these LED strips will be controlled by BF firmware
RSSI pad:Support. Labeled as RS
SmartPort:Support. You can use any set of serial port TX
Supported flight controller firmware:BetaFlight (default), EMUFlight, INAV
Firmware target name:SPEEDYBEEF405V3
Mount:30.5x30.5mm (4mm hole diameter)
Dimensions:41.6(L) x 39.4(W) x 7.8(H) mm
Weight:9.6g

SpeedyBee BLS 50A 4-in-1 ESC
Firmware:LHeli_S JH50
Wireless configuration:Full configuration supported by SpeedyBee App
PC configurator download link:ttps://esc-configurator.com/
Continuous Current:50A*4
Break current:55A (5S)
Protective Diode for TV:Yes
External Capacitor:1500uF Low ESR Capacitor (included in the package)
Protocol ESC:DSHOT300/600
Power Input:3-6S LiPo
Output power:VBAT
Current sensor:Support (scale=386 offset=0)
Mount:30.5x30.5mm (4mm hole diameter)
Dimensions:45.6(L)*44(W)*6.1mm(H)
Weight:13.8g